Search results for all lists

10000 messages found
Sort by
List: trawlers@lists.trawlering.com
From: Don Sorensen
 
Re: T&T: Mathers (was Single Handing)
Sat, Sep 3, 2005 5:10 PM
. > > I had my Mathers die on me. It was due to a manufacturing > defect. Fortunately I had just finished tying to the dock. It took me Wray Your ideas are right on. I have seen other units, Glendenning, that have a manual choke cable system which would be used in an emergency.
List: trawlers@lists.trawlering.com
From: Keith
 
Re: T&T: BUYING AND INSTALLING A BOW THRUSTER
Fri, Jan 20, 2006 9:30 AM
Keith _____ Health is merely the slowest possible rate at which one can die. ----- Original Message ----- From: "AL SOUZA" >I will be buying a bow thruster this spring. Being new to trawling what >should I be looking for in the selection of a thruster? Are there any >complaints that anyone has with the thruster on their boat?
List: trawlers@lists.trawlering.com
From: Keith
 
Re: T&T: De Scaling Heat Exchangers
Wed, Aug 22, 2007 5:41 PM
Keith _____ "If there are no dogs in Heaven, then when I die I want to go where they went."
List: trawlers@lists.trawlering.com
From: Larry N. Brown
 
Fw: Women?
Tue, Oct 23, 2007 6:03 PM
Just remember the adage: 'Old > sailors > never die, they just move on to trawlers that go the same slow speed... > but > are more comfortable'...or something like that. Age? Not that it matters, > but > coming on 77 next month. I have also been up/down the east coast ICW > several > times. What's your point?
List: trawlers@lists.trawlering.com
From: Wayne & Lynn Flatt
 
Requiem for John Camm
Thu, Apr 2, 2009 2:04 PM
Under the wide and starry sky Dig the grave and let me lie: Glad did I live and gladly die, And I laid me down with a will. This be the verse you  grave for me: Here he lies where he longd to be; Home is the sailor, home from the sea, And the hunter home from the hill.
List: trawlers@lists.trawlering.com
From: Rudy and Jill
 
Re: T&T: perko 493 repair
Fri, Jan 22, 2010 5:37 PM
With a hacksaw and appropriately sized threading die, you can easily make replacement rods with brass rod purchased locally. Stainless steel rod can also be used. I've done both without any long term detrimental effects. I believe that the tie rod in your unit is 1/4 inch.
List: trawlers@lists.trawlering.com
From: edmond badham
 
2nd bilge pump
Sat, Aug 5, 2017 12:53 PM
This is partly caused by a check valve in the line which I use to prevent pump cycling (until the batteries die) (yes I agree they can not be used in lieu of a discharge loop). To remedy the air lock I drilled a very small hole (1/8") in the output flange not covered by the hose. I'm happy with this set up.
List: discuss@lists.openscad.org
From: Joseph Lenox
 
Re: [OpenSCAD] Compiling for 64 bit Sparc Solaris 10
Fri, Feb 6, 2015 9:45 AM
On Feb 6, 2015 3:29 AM, "MichaelAtOz" wrote: > > Joseph Lenox wrote > > So you're going to get this working or die trying? > > Almost choked on my wine...
List: discuss@lists.openscad.org
From: Torsten Paul
 
Re: [OpenSCAD] What to call "variables"
Wed, Sep 7, 2016 12:13 PM
While there are probably a number of use cases where external programs using OpenSCAD as backend make very much sense, it's still a bit sad to see all those projects started with huge enthusiasm die after half a year or so when it gets hard to continue supporting users. ciao, Torsten.
List: usrp-users@lists.ettus.com
From: Steven Knudsen
 
Re: [USRP-users] USRP command port
Thu, Apr 20, 2017 3:36 PM
good luck, steven Steven Knudsen, Ph.D., P.Eng. www. techconficio.ca www.linkedin.com/in/knudstevenknudsen Du bist die Aufgabe.