metal and, using > epoxy and > fiberglass, glass on a new top, over the existing top. > Works pretty good. > Did this with one of those huge storage tanks that are > found at fuel > terminals... yep, covered the entire domed top that was > rusting thru, so it > isn't necessarily something to scoff at. > > If possible, maybe just a stop gap, then too, maybe more

/top/USRP2/u2_core.v:617: error: Unknown module type: vita_rx_chain > ../sdr_lib/dsp_core_rx.v:148: error: Unknown module type: sfft > ../top/USRP2/u2_core.v:645: error: Unknown module type: vita_rx_chain > ../top/USRP2/u2_core.v:666: error: Unknown module type: ext_fifo > ../top/USRP2/u2_core.v:694: error: Unknown module type: vita_tx_chain > ..

/uhd/fpga-src/usrp3/top/tcl/ise_helper.tcl "" make[1]: Leaving directory `/home/nodeuser/data/alt_iris/uhd_fpga/uhd/fpga-src/usrp3/top/b200' Generated /home/nodeuser/data/alt_iris/uhd_fpga/uhd/fpga-src/usrp3/top/b200/build-B210/b200.xise Project Generation DONE ...

Please run setupenv.sh" You need to source the setupenv.sh script which is located in the fpga-src/usrp3/top/x300 directory before running the make command.

Try visiting club websites for dates and contacts. A list of nature club with websites can be found at the Ontario Nature website, click on the map at to find a group near you. -- Mark Cranford ONTBIRDS Coordinator Mississauga, Ont. mark.cranford@ofo.ca 905 279 9576

'/home/user/offline/src/fpga/usrp3/top/x300/build-ip/xc7k410tffg900-2/ten_gig_eth_pcs_pma/ten_gig_eth_pcs_pma.xci.out' failed make[1]: *** [/home/user/offline/src/fpga/usrp3/top/x300/build-ip/xc7k410tffg900-2/ten_gig_eth_pcs_pma/ten_gig_eth_pcs_pma.xci.out] Error 1 make[1]: Leaving directory '/home/user/offline/src/fpga/usrp3/top/x300' Makefile:119: recipe for

for target '/home/user/offline/src/fpga/usrp3/top/x300/build-ip/xc7k410tffg900-2/ten_gig_eth_pcs_pma/ten_gig_eth_pcs_pma.xci.out' failed > make[1]: *** [/home/user/offline/src/fpga/usrp3/top/x300/build-ip/xc7k410tffg900-2/ten_gig_eth_pcs_pma/ten_gig_eth_pcs_pma.xci.out] Error 1 > make[1]: Leaving directory '/home/user/offline/src/fpga/usrp3/top/x300' > Makefile

THIS IS A DUPLICATE EMAIL BECAUSE I NOW HAVE A WEBSITE WITH PHOTOS AVAILABLE. 1980 41' CHB Aft Cabin Trawler, Twin 120hp Diesel engines, new canvas & Plexiglas, fully enclosed fly bridge, Queen in aft cabin. On the water in Marina del Rey, CA. See WEBSITE. http://home.earthlink.net/~lesterces/

However ever hopeful I would like to know the website. I inadvertantly deleted the E Mail with the website listed. Also is it possible to use biobor as well, and at the same time. Art Nathan Lady Jane Annapolis, MD

'Lo All, For those of you with Garmin G-Charts, the following is copied from the Garmin website: OffShore G-Charts will no longer be sold or supported after 11/30/04. Garmin Website for G-Charts: http://www.garmin.com/cartography/offshore/ Take care and be safe. Wayne M/V Celestial Albin43 Sundeck