Hi Bharat, The log does help. The UAS said in its 422/INVITE response that Min-SE is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains Session-expires header with value less than Min-SE header in INVITE request, so BYE was sent. The faulty UA here is the UAS, take a look at RFC 4028 Section 9: === If the UAS wishes to accept the request, it copies the value of the Session-Expires header field from the request into the 2xx response. The UAS response MAY reduce its value but MUST NOT set it to a duration lower than the value in the Min-SE header field in the request, if it is present; === However, I've just created ticket #954 (Session Timer issues) and considered to put this case in. Thanks for the report, nanang On Fri, Aug 21, 2009 at 7:04 PM, Bharat Yadav<bharat.yadav@axisconvergence.com> wrote: > Dear Nanang > Here is trace logs of symbian_ua and Wireshark. > Thanks and regards > Bharat > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Bharat Yadav > Sent: Friday, August 21, 2009 5:10 PM > To: 'pjsip list' > Subject: Re: [pjsip] Session Timer Too Small > > Dear Nanang > Thanks for quick reply. First of all when I want to make call with G711 it > will ok and call get connected and I hangup the call gracefully, but if I > only use G729 for that case when call made at the stage of Ringing if > recipient accept the call it shows "Session Timer Too small" and get hanged > with "normal call clearing" message. From the log end with will send the log > file within as while. > Thanks > Bharat > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Friday, August 21, 2009 4:52 PM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Hi Bharat, > > I don't think I get this right. There shouldn't be a problem when a > caller gets 422 response (session timer too small), it will just > re-try to send INVITE with acceptable session interval as specified by > the 422 response automatically (no config setting to be set/modified > here). > > So, did you experience other than the above scenario? Log file or > clear reproducing steps could be helpful. > > Regards, > nanang > > > On Fri, Aug 21, 2009 at 5:24 PM, Bharat > Yadav<bharat.yadav@axisconvergence.com> wrote: >> Hi all >> >> I am using 1.4 trunk and trying to implement VAS for FP1 using symbian_ua >> all are fine for Ringing stage when call connect to GSM phone using G729 > it >> show "Session Timer Too Small", how should and where I define session time >> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >> session timer expression. Please help. >> >> Thanks >> >> Bharat >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > > > > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > >

Hi Bharat, Just want to update you regarding this issue. There was update on ticket #954, i.e: rev 2933-2934, to handle this case. Please drop in any feedback once you've got a chance to test it, thanks. BR, nanang On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: > Hi Bharat, > > The log does help. The UAS said in its 422/INVITE response that Min-SE > is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The > symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains > Session-expires header with value less than Min-SE header in INVITE > request, so BYE was sent. > > The faulty UA here is the UAS, take a look at RFC 4028 Section 9: > === > If the UAS wishes to accept the request, it copies the value of the > Session-Expires header field from the request into the 2xx response. > The UAS response MAY reduce its value but MUST NOT set it to a > duration lower than the value in the Min-SE header field in the > request, if it is present; > === > > However, I've just created ticket #954 (Session Timer issues) and > considered to put this case in. > > Thanks for the report, > nanang > > > On Fri, Aug 21, 2009 at 7:04 PM, Bharat > Yadav<bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> Here is trace logs of symbian_ua and Wireshark. >> Thanks and regards >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Bharat Yadav >> Sent: Friday, August 21, 2009 5:10 PM >> To: 'pjsip list' >> Subject: Re: [pjsip] Session Timer Too Small >> >> Dear Nanang >> Thanks for quick reply. First of all when I want to make call with G711 it >> will ok and call get connected and I hangup the call gracefully, but if I >> only use G729 for that case when call made at the stage of Ringing if >> recipient accept the call it shows "Session Timer Too small" and get hanged >> with "normal call clearing" message. From the log end with will send the log >> file within as while. >> Thanks >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Friday, August 21, 2009 4:52 PM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> I don't think I get this right. There shouldn't be a problem when a >> caller gets 422 response (session timer too small), it will just >> re-try to send INVITE with acceptable session interval as specified by >> the 422 response automatically (no config setting to be set/modified >> here). >> >> So, did you experience other than the above scenario? Log file or >> clear reproducing steps could be helpful. >> >> Regards, >> nanang >> >> >> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Hi all >>> >>> I am using 1.4 trunk and trying to implement VAS for FP1 using symbian_ua >>> all are fine for Ringing stage when call connect to GSM phone using G729 >> it >>> show "Session Timer Too Small", how should and where I define session time >>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>> session timer expression. Please help. >>> >>> Thanks >>> >>> Bharat >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >

Dear Nanang Thanks for info, I will check it some while within 1-2day and let you know. Thanks and regards Happy Deepawali(Festival of Lights) Bharat Yadav -----Original Message----- From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] On Behalf Of Nanang Izzuddin Sent: Thursday, October 15, 2009 10:15 AM To: pjsip list Subject: Re: [pjsip] Session Timer Too Small Hi Bharat, Just want to update you regarding this issue. There was update on ticket #954, i.e: rev 2933-2934, to handle this case. Please drop in any feedback once you've got a chance to test it, thanks. BR, nanang On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: > Hi Bharat, > > The log does help. The UAS said in its 422/INVITE response that Min-SE > is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The > symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains > Session-expires header with value less than Min-SE header in INVITE > request, so BYE was sent. > > The faulty UA here is the UAS, take a look at RFC 4028 Section 9: > === > If the UAS wishes to accept the request, it copies the value of the > Session-Expires header field from the request into the 2xx response. > The UAS response MAY reduce its value but MUST NOT set it to a > duration lower than the value in the Min-SE header field in the > request, if it is present; > === > > However, I've just created ticket #954 (Session Timer issues) and > considered to put this case in. > > Thanks for the report, > nanang > > > On Fri, Aug 21, 2009 at 7:04 PM, Bharat > Yadav<bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> Here is trace logs of symbian_ua and Wireshark. >> Thanks and regards >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Bharat Yadav >> Sent: Friday, August 21, 2009 5:10 PM >> To: 'pjsip list' >> Subject: Re: [pjsip] Session Timer Too Small >> >> Dear Nanang >> Thanks for quick reply. First of all when I want to make call with G711 it >> will ok and call get connected and I hangup the call gracefully, but if I >> only use G729 for that case when call made at the stage of Ringing if >> recipient accept the call it shows "Session Timer Too small" and get hanged >> with "normal call clearing" message. From the log end with will send the log >> file within as while. >> Thanks >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Friday, August 21, 2009 4:52 PM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> I don't think I get this right. There shouldn't be a problem when a >> caller gets 422 response (session timer too small), it will just >> re-try to send INVITE with acceptable session interval as specified by >> the 422 response automatically (no config setting to be set/modified >> here). >> >> So, did you experience other than the above scenario? Log file or >> clear reproducing steps could be helpful. >> >> Regards, >> nanang >> >> >> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Hi all >>> >>> I am using 1.4 trunk and trying to implement VAS for FP1 using symbian_ua >>> all are fine for Ringing stage when call connect to GSM phone using G729 >> it >>> show "Session Timer Too Small", how should and where I define session time >>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>> session timer expression. Please help. >>> >>> Thanks >>> >>> Bharat >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > _______________________________________________ Visit our blog: http://blog.pjsip.org pjsip mailing list pjsip@lists.pjsip.org http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org

Dear Nanang I tested Session timer fix but still having same as before. Wireshark trace attached. Thanks and regards Bharat Yadav -----Original Message----- From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] On Behalf Of Nanang Izzuddin Sent: Thursday, October 15, 2009 10:15 AM To: pjsip list Subject: Re: [pjsip] Session Timer Too Small Hi Bharat, Just want to update you regarding this issue. There was update on ticket #954, i.e: rev 2933-2934, to handle this case. Please drop in any feedback once you've got a chance to test it, thanks. BR, nanang On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: > Hi Bharat, > > The log does help. The UAS said in its 422/INVITE response that Min-SE > is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The > symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains > Session-expires header with value less than Min-SE header in INVITE > request, so BYE was sent. > > The faulty UA here is the UAS, take a look at RFC 4028 Section 9: > === > If the UAS wishes to accept the request, it copies the value of the > Session-Expires header field from the request into the 2xx response. > The UAS response MAY reduce its value but MUST NOT set it to a > duration lower than the value in the Min-SE header field in the > request, if it is present; > === > > However, I've just created ticket #954 (Session Timer issues) and > considered to put this case in. > > Thanks for the report, > nanang > > > On Fri, Aug 21, 2009 at 7:04 PM, Bharat > Yadav<bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> Here is trace logs of symbian_ua and Wireshark. >> Thanks and regards >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Bharat Yadav >> Sent: Friday, August 21, 2009 5:10 PM >> To: 'pjsip list' >> Subject: Re: [pjsip] Session Timer Too Small >> >> Dear Nanang >> Thanks for quick reply. First of all when I want to make call with G711 it >> will ok and call get connected and I hangup the call gracefully, but if I >> only use G729 for that case when call made at the stage of Ringing if >> recipient accept the call it shows "Session Timer Too small" and get hanged >> with "normal call clearing" message. From the log end with will send the log >> file within as while. >> Thanks >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Friday, August 21, 2009 4:52 PM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> I don't think I get this right. There shouldn't be a problem when a >> caller gets 422 response (session timer too small), it will just >> re-try to send INVITE with acceptable session interval as specified by >> the 422 response automatically (no config setting to be set/modified >> here). >> >> So, did you experience other than the above scenario? Log file or >> clear reproducing steps could be helpful. >> >> Regards, >> nanang >> >> >> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Hi all >>> >>> I am using 1.4 trunk and trying to implement VAS for FP1 using symbian_ua >>> all are fine for Ringing stage when call connect to GSM phone using G729 >> it >>> show "Session Timer Too Small", how should and where I define session time >>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>> session timer expression. Please help. >>> >>> Thanks >>> >>> Bharat >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > _______________________________________________ Visit our blog: http://blog.pjsip.org pjsip mailing list pjsip@lists.pjsip.org http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org

Dear Nanang I tested Session timer fix with revision svn 2961 but still having same as before. Wireshark trace attached.(forget to attach file now with this one) Thanks and regards Bharat Yadav -----Original Message----- From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] On Behalf Of Nanang Izzuddin Sent: Thursday, October 15, 2009 10:15 AM To: pjsip list Subject: Re: [pjsip] Session Timer Too Small Hi Bharat, Just want to update you regarding this issue. There was update on ticket #954, i.e: rev 2933-2934, to handle this case. Please drop in any feedback once you've got a chance to test it, thanks. BR, nanang On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: > Hi Bharat, > > The log does help. The UAS said in its 422/INVITE response that Min-SE > is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The > symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains > Session-expires header with value less than Min-SE header in INVITE > request, so BYE was sent. > > The faulty UA here is the UAS, take a look at RFC 4028 Section 9: > === > If the UAS wishes to accept the request, it copies the value of the > Session-Expires header field from the request into the 2xx response. > The UAS response MAY reduce its value but MUST NOT set it to a > duration lower than the value in the Min-SE header field in the > request, if it is present; > === > > However, I've just created ticket #954 (Session Timer issues) and > considered to put this case in. > > Thanks for the report, > nanang > > > On Fri, Aug 21, 2009 at 7:04 PM, Bharat > Yadav<bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> Here is trace logs of symbian_ua and Wireshark. >> Thanks and regards >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Bharat Yadav >> Sent: Friday, August 21, 2009 5:10 PM >> To: 'pjsip list' >> Subject: Re: [pjsip] Session Timer Too Small >> >> Dear Nanang >> Thanks for quick reply. First of all when I want to make call with G711 it >> will ok and call get connected and I hangup the call gracefully, but if I >> only use G729 for that case when call made at the stage of Ringing if >> recipient accept the call it shows "Session Timer Too small" and get hanged >> with "normal call clearing" message. From the log end with will send the log >> file within as while. >> Thanks >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Friday, August 21, 2009 4:52 PM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> I don't think I get this right. There shouldn't be a problem when a >> caller gets 422 response (session timer too small), it will just >> re-try to send INVITE with acceptable session interval as specified by >> the 422 response automatically (no config setting to be set/modified >> here). >> >> So, did you experience other than the above scenario? Log file or >> clear reproducing steps could be helpful. >> >> Regards, >> nanang >> >> >> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Hi all >>> >>> I am using 1.4 trunk and trying to implement VAS for FP1 using symbian_ua >>> all are fine for Ringing stage when call connect to GSM phone using G729 >> it >>> show "Session Timer Too Small", how should and where I define session time >>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>> session timer expression. Please help. >>> >>> Thanks >>> >>> Bharat >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > _______________________________________________ Visit our blog: http://blog.pjsip.org pjsip mailing list pjsip@lists.pjsip.org http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org

Bharat, Unfortunately the wireshark trace couldn't be opened here, and I think it may be better to see the pjsua log file, as the patch would print some warning message regarding the issue in the log file. BR, nanang On Fri, Oct 23, 2009 at 12:28 PM, Bharat Yadav <bharat.yadav@axisconvergence.com> wrote: > Dear Nanang > I tested Session timer fix with revision svn 2961 but still having same as > before. Wireshark trace attached.(forget to attach file now with this one) > Thanks and regards > Bharat Yadav > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Thursday, October 15, 2009 10:15 AM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Hi Bharat, > > Just want to update you regarding this issue. There was update on > ticket #954, i.e: rev 2933-2934, to handle this case. > > Please drop in any feedback once you've got a chance to test it, thanks. > > BR, > nanang > > > On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: >> Hi Bharat, >> >> The log does help. The UAS said in its 422/INVITE response that Min-SE >> is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The >> symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains >> Session-expires header with value less than Min-SE header in INVITE >> request, so BYE was sent. >> >> The faulty UA here is the UAS, take a look at RFC 4028 Section 9: >> === >> If the UAS wishes to accept the request, it copies the value of the >> Session-Expires header field from the request into the 2xx response. >> The UAS response MAY reduce its value but MUST NOT set it to a >> duration lower than the value in the Min-SE header field in the >> request, if it is present; >> === >> >> However, I've just created ticket #954 (Session Timer issues) and >> considered to put this case in. >> >> Thanks for the report, >> nanang >> >> >> On Fri, Aug 21, 2009 at 7:04 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Dear Nanang >>> Here is trace logs of symbian_ua and Wireshark. >>> Thanks and regards >>> Bharat >>> >>> -----Original Message----- >>> From: pjsip-bounces@lists.pjsip.org > [mailto:pjsip-bounces@lists.pjsip.org] >>> On Behalf Of Bharat Yadav >>> Sent: Friday, August 21, 2009 5:10 PM >>> To: 'pjsip list' >>> Subject: Re: [pjsip] Session Timer Too Small >>> >>> Dear Nanang >>> Thanks for quick reply. First of all when I want to make call with G711 > it >>> will ok and call get connected and I hangup the call gracefully, but if I >>> only use G729 for that case when call made at the stage of Ringing if >>> recipient accept the call it shows "Session Timer Too small" and get > hanged >>> with "normal call clearing" message. From the log end with will send the > log >>> file within as while. >>> Thanks >>> Bharat >>> >>> -----Original Message----- >>> From: pjsip-bounces@lists.pjsip.org > [mailto:pjsip-bounces@lists.pjsip.org] >>> On Behalf Of Nanang Izzuddin >>> Sent: Friday, August 21, 2009 4:52 PM >>> To: pjsip list >>> Subject: Re: [pjsip] Session Timer Too Small >>> >>> Hi Bharat, >>> >>> I don't think I get this right. There shouldn't be a problem when a >>> caller gets 422 response (session timer too small), it will just >>> re-try to send INVITE with acceptable session interval as specified by >>> the 422 response automatically (no config setting to be set/modified >>> here). >>> >>> So, did you experience other than the above scenario? Log file or >>> clear reproducing steps could be helpful. >>> >>> Regards, >>> nanang >>> >>> >>> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>> Hi all >>>> >>>> I am using 1.4 trunk and trying to implement VAS for FP1 using > symbian_ua >>>> all are fine for Ringing stage when call connect to GSM phone using G729 >>> it >>>> show "Session Timer Too Small", how should and where I define session > time >>>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>>> session timer expression. Please help. >>>> >>>> Thanks >>>> >>>> Bharat >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >>> >>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > >

Dear Nanang Welcome back, here is application symbian_ua_gui log and wireshark log too(in text mode) it should help to resolve this issue. Thanks Bharat -----Original Message----- From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] On Behalf Of Nanang Izzuddin Sent: Wednesday, October 28, 2009 1:45 PM To: pjsip list Subject: Re: [pjsip] Session Timer Too Small Bharat, Unfortunately the wireshark trace couldn't be opened here, and I think it may be better to see the pjsua log file, as the patch would print some warning message regarding the issue in the log file. BR, nanang On Fri, Oct 23, 2009 at 12:28 PM, Bharat Yadav <bharat.yadav@axisconvergence.com> wrote: > Dear Nanang > I tested Session timer fix with revision svn 2961 but still having same as > before. Wireshark trace attached.(forget to attach file now with this one) > Thanks and regards > Bharat Yadav > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Thursday, October 15, 2009 10:15 AM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Hi Bharat, > > Just want to update you regarding this issue. There was update on > ticket #954, i.e: rev 2933-2934, to handle this case. > > Please drop in any feedback once you've got a chance to test it, thanks. > > BR, > nanang > > > On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> wrote: >> Hi Bharat, >> >> The log does help. The UAS said in its 422/INVITE response that Min-SE >> is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The >> symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains >> Session-expires header with value less than Min-SE header in INVITE >> request, so BYE was sent. >> >> The faulty UA here is the UAS, take a look at RFC 4028 Section 9: >> === >> If the UAS wishes to accept the request, it copies the value of the >> Session-Expires header field from the request into the 2xx response. >> The UAS response MAY reduce its value but MUST NOT set it to a >> duration lower than the value in the Min-SE header field in the >> request, if it is present; >> === >> >> However, I've just created ticket #954 (Session Timer issues) and >> considered to put this case in. >> >> Thanks for the report, >> nanang >> >> >> On Fri, Aug 21, 2009 at 7:04 PM, Bharat >> Yadav<bharat.yadav@axisconvergence.com> wrote: >>> Dear Nanang >>> Here is trace logs of symbian_ua and Wireshark. >>> Thanks and regards >>> Bharat >>> >>> -----Original Message----- >>> From: pjsip-bounces@lists.pjsip.org > [mailto:pjsip-bounces@lists.pjsip.org] >>> On Behalf Of Bharat Yadav >>> Sent: Friday, August 21, 2009 5:10 PM >>> To: 'pjsip list' >>> Subject: Re: [pjsip] Session Timer Too Small >>> >>> Dear Nanang >>> Thanks for quick reply. First of all when I want to make call with G711 > it >>> will ok and call get connected and I hangup the call gracefully, but if I >>> only use G729 for that case when call made at the stage of Ringing if >>> recipient accept the call it shows "Session Timer Too small" and get > hanged >>> with "normal call clearing" message. From the log end with will send the > log >>> file within as while. >>> Thanks >>> Bharat >>> >>> -----Original Message----- >>> From: pjsip-bounces@lists.pjsip.org > [mailto:pjsip-bounces@lists.pjsip.org] >>> On Behalf Of Nanang Izzuddin >>> Sent: Friday, August 21, 2009 4:52 PM >>> To: pjsip list >>> Subject: Re: [pjsip] Session Timer Too Small >>> >>> Hi Bharat, >>> >>> I don't think I get this right. There shouldn't be a problem when a >>> caller gets 422 response (session timer too small), it will just >>> re-try to send INVITE with acceptable session interval as specified by >>> the 422 response automatically (no config setting to be set/modified >>> here). >>> >>> So, did you experience other than the above scenario? Log file or >>> clear reproducing steps could be helpful. >>> >>> Regards, >>> nanang >>> >>> >>> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>> Hi all >>>> >>>> I am using 1.4 trunk and trying to implement VAS for FP1 using > symbian_ua >>>> all are fine for Ringing stage when call connect to GSM phone using G729 >>> it >>>> show "Session Timer Too Small", how should and where I define session > time >>>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>>> session timer expression. Please help. >>>> >>>> Thanks >>>> >>>> Bharat >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >>> >>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > _______________________________________________ Visit our blog: http://blog.pjsip.org pjsip mailing list pjsip@lists.pjsip.org http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org

Hi Bharat, Well, cannot find any log attached. However, there has just been a fix that could be related to this issue, please see ticket #975 [1]. -- [1] http://trac.pjsip.org/repos/ticket/975 -- BR, nanang On Wed, Oct 28, 2009 at 4:08 PM, Bharat Yadav <bharat.yadav@axisconvergence.com> wrote: > Dear Nanang > Welcome back, here is application symbian_ua_gui log and wireshark log > too(in text mode) it should help to resolve this issue. > Thanks > Bharat > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Wednesday, October 28, 2009 1:45 PM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Bharat, > > Unfortunately the wireshark trace couldn't be opened here, and I think > it may be better to see the pjsua log file, as the patch would print > some warning message regarding the issue in the log file. > > BR, > nanang > > > On Fri, Oct 23, 2009 at 12:28 PM, Bharat Yadav > <bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> I tested Session timer fix with revision svn 2961 but still having same as >> before. Wireshark trace attached.(forget to attach file now with this one) >> Thanks and regards >> Bharat Yadav >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Thursday, October 15, 2009 10:15 AM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> Just want to update you regarding this issue. There was update on >> ticket #954, i.e: rev 2933-2934, to handle this case. >> >> Please drop in any feedback once you've got a chance to test it, thanks. >> >> BR, >> nanang >> >> >> On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> > wrote: >>> Hi Bharat, >>> >>> The log does help. The UAS said in its 422/INVITE response that Min-SE >>> is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The >>> symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains >>> Session-expires header with value less than Min-SE header in INVITE >>> request, so BYE was sent. >>> >>> The faulty UA here is the UAS, take a look at RFC 4028 Section 9: >>> === >>> If the UAS wishes to accept the request, it copies the value of the >>> Session-Expires header field from the request into the 2xx response. >>> The UAS response MAY reduce its value but MUST NOT set it to a >>> duration lower than the value in the Min-SE header field in the >>> request, if it is present; >>> === >>> >>> However, I've just created ticket #954 (Session Timer issues) and >>> considered to put this case in. >>> >>> Thanks for the report, >>> nanang >>> >>> >>> On Fri, Aug 21, 2009 at 7:04 PM, Bharat >>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>> Dear Nanang >>>> Here is trace logs of symbian_ua and Wireshark. >>>> Thanks and regards >>>> Bharat >>>> >>>> -----Original Message----- >>>> From: pjsip-bounces@lists.pjsip.org >> [mailto:pjsip-bounces@lists.pjsip.org] >>>> On Behalf Of Bharat Yadav >>>> Sent: Friday, August 21, 2009 5:10 PM >>>> To: 'pjsip list' >>>> Subject: Re: [pjsip] Session Timer Too Small >>>> >>>> Dear Nanang >>>> Thanks for quick reply. First of all when I want to make call with G711 >> it >>>> will ok and call get connected and I hangup the call gracefully, but if > I >>>> only use G729 for that case when call made at the stage of Ringing if >>>> recipient accept the call it shows "Session Timer Too small" and get >> hanged >>>> with "normal call clearing" message. From the log end with will send the >> log >>>> file within as while. >>>> Thanks >>>> Bharat >>>> >>>> -----Original Message----- >>>> From: pjsip-bounces@lists.pjsip.org >> [mailto:pjsip-bounces@lists.pjsip.org] >>>> On Behalf Of Nanang Izzuddin >>>> Sent: Friday, August 21, 2009 4:52 PM >>>> To: pjsip list >>>> Subject: Re: [pjsip] Session Timer Too Small >>>> >>>> Hi Bharat, >>>> >>>> I don't think I get this right. There shouldn't be a problem when a >>>> caller gets 422 response (session timer too small), it will just >>>> re-try to send INVITE with acceptable session interval as specified by >>>> the 422 response automatically (no config setting to be set/modified >>>> here). >>>> >>>> So, did you experience other than the above scenario? Log file or >>>> clear reproducing steps could be helpful. >>>> >>>> Regards, >>>> nanang >>>> >>>> >>>> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >>>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>>> Hi all >>>>> >>>>> I am using 1.4 trunk and trying to implement VAS for FP1 using >> symbian_ua >>>>> all are fine for Ringing stage when call connect to GSM phone using > G729 >>>> it >>>>> show "Session Timer Too Small", how should and where I define session >> time >>>>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>>>> session timer expression. Please help. >>>>> >>>>> Thanks >>>>> >>>>> Bharat >>>>> >>>>> _______________________________________________ >>>>> Visit our blog: http://blog.pjsip.org >>>>> >>>>> pjsip mailing list >>>>> pjsip@lists.pjsip.org >>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>> >>>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >

Hi Nanang I updated trunk with current svn2984 but issue remained same. Please find attached file with current symbian_ua_gui.log Thanks and regards Bharat -----Original Message----- From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] On Behalf Of Nanang Izzuddin Sent: Wednesday, November 04, 2009 12:08 PM To: pjsip list Subject: Re: [pjsip] Session Timer Too Small Hi Bharat, Well, cannot find any log attached. However, there has just been a fix that could be related to this issue, please see ticket #975 [1]. -- [1] http://trac.pjsip.org/repos/ticket/975 -- BR, nanang On Wed, Oct 28, 2009 at 4:08 PM, Bharat Yadav <bharat.yadav@axisconvergence.com> wrote: > Dear Nanang > Welcome back, here is application symbian_ua_gui log and wireshark log > too(in text mode) it should help to resolve this issue. > Thanks > Bharat > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Wednesday, October 28, 2009 1:45 PM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Bharat, > > Unfortunately the wireshark trace couldn't be opened here, and I think > it may be better to see the pjsua log file, as the patch would print > some warning message regarding the issue in the log file. > > BR, > nanang > > > On Fri, Oct 23, 2009 at 12:28 PM, Bharat Yadav > <bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> I tested Session timer fix with revision svn 2961 but still having same as >> before. Wireshark trace attached.(forget to attach file now with this one) >> Thanks and regards >> Bharat Yadav >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Thursday, October 15, 2009 10:15 AM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Hi Bharat, >> >> Just want to update you regarding this issue. There was update on >> ticket #954, i.e: rev 2933-2934, to handle this case. >> >> Please drop in any feedback once you've got a chance to test it, thanks. >> >> BR, >> nanang >> >> >> On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> > wrote: >>> Hi Bharat, >>> >>> The log does help. The UAS said in its 422/INVITE response that Min-SE >>> is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The >>> symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains >>> Session-expires header with value less than Min-SE header in INVITE >>> request, so BYE was sent. >>> >>> The faulty UA here is the UAS, take a look at RFC 4028 Section 9: >>> === >>> If the UAS wishes to accept the request, it copies the value of the >>> Session-Expires header field from the request into the 2xx response. >>> The UAS response MAY reduce its value but MUST NOT set it to a >>> duration lower than the value in the Min-SE header field in the >>> request, if it is present; >>> === >>> >>> However, I've just created ticket #954 (Session Timer issues) and >>> considered to put this case in. >>> >>> Thanks for the report, >>> nanang >>> >>> >>> On Fri, Aug 21, 2009 at 7:04 PM, Bharat >>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>> Dear Nanang >>>> Here is trace logs of symbian_ua and Wireshark. >>>> Thanks and regards >>>> Bharat >>>> >>>> -----Original Message----- >>>> From: pjsip-bounces@lists.pjsip.org >> [mailto:pjsip-bounces@lists.pjsip.org] >>>> On Behalf Of Bharat Yadav >>>> Sent: Friday, August 21, 2009 5:10 PM >>>> To: 'pjsip list' >>>> Subject: Re: [pjsip] Session Timer Too Small >>>> >>>> Dear Nanang >>>> Thanks for quick reply. First of all when I want to make call with G711 >> it >>>> will ok and call get connected and I hangup the call gracefully, but if > I >>>> only use G729 for that case when call made at the stage of Ringing if >>>> recipient accept the call it shows "Session Timer Too small" and get >> hanged >>>> with "normal call clearing" message. From the log end with will send the >> log >>>> file within as while. >>>> Thanks >>>> Bharat >>>> >>>> -----Original Message----- >>>> From: pjsip-bounces@lists.pjsip.org >> [mailto:pjsip-bounces@lists.pjsip.org] >>>> On Behalf Of Nanang Izzuddin >>>> Sent: Friday, August 21, 2009 4:52 PM >>>> To: pjsip list >>>> Subject: Re: [pjsip] Session Timer Too Small >>>> >>>> Hi Bharat, >>>> >>>> I don't think I get this right. There shouldn't be a problem when a >>>> caller gets 422 response (session timer too small), it will just >>>> re-try to send INVITE with acceptable session interval as specified by >>>> the 422 response automatically (no config setting to be set/modified >>>> here). >>>> >>>> So, did you experience other than the above scenario? Log file or >>>> clear reproducing steps could be helpful. >>>> >>>> Regards, >>>> nanang >>>> >>>> >>>> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >>>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>>> Hi all >>>>> >>>>> I am using 1.4 trunk and trying to implement VAS for FP1 using >> symbian_ua >>>>> all are fine for Ringing stage when call connect to GSM phone using > G729 >>>> it >>>>> show "Session Timer Too Small", how should and where I define session >> time >>>>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>>>> session timer expression. Please help. >>>>> >>>>> Thanks >>>>> >>>>> Bharat >>>>> >>>>> _______________________________________________ >>>>> Visit our blog: http://blog.pjsip.org >>>>> >>>>> pjsip mailing list >>>>> pjsip@lists.pjsip.org >>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>> >>>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>>> _______________________________________________ >>>> Visit our blog: http://blog.pjsip.org >>>> >>>> pjsip mailing list >>>> pjsip@lists.pjsip.org >>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>> >>>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > _______________________________________________ Visit our blog: http://blog.pjsip.org pjsip mailing list pjsip@lists.pjsip.org http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org

Hi Bharat, Just created a sipp test scenario for bad SE in 200 response, SVN trunk r2987, and pjsua passed this test. So, well, there could be another problem. Have you ever tried to use pjsua making call via the same gateway? Also, sorry forgot to mention this before, more verbose log, i.e: log level 5, would be great. BR, nanang On Wed, Nov 4, 2009 at 4:19 PM, Bharat Yadav <bharat.yadav@axisconvergence.com> wrote: > Hi Nanang > I updated trunk with current svn2984 but issue remained same. > Please find attached file with current symbian_ua_gui.log > Thanks and regards > Bharat > > -----Original Message----- > From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] > On Behalf Of Nanang Izzuddin > Sent: Wednesday, November 04, 2009 12:08 PM > To: pjsip list > Subject: Re: [pjsip] Session Timer Too Small > > Hi Bharat, > > Well, cannot find any log attached. However, there has just been a fix > that could be related to this issue, please see ticket #975 [1]. > > -- > [1] http://trac.pjsip.org/repos/ticket/975 > -- > > BR, > nanang > > > On Wed, Oct 28, 2009 at 4:08 PM, Bharat Yadav > <bharat.yadav@axisconvergence.com> wrote: >> Dear Nanang >> Welcome back, here is application symbian_ua_gui log and wireshark log >> too(in text mode) it should help to resolve this issue. >> Thanks >> Bharat >> >> -----Original Message----- >> From: pjsip-bounces@lists.pjsip.org [mailto:pjsip-bounces@lists.pjsip.org] >> On Behalf Of Nanang Izzuddin >> Sent: Wednesday, October 28, 2009 1:45 PM >> To: pjsip list >> Subject: Re: [pjsip] Session Timer Too Small >> >> Bharat, >> >> Unfortunately the wireshark trace couldn't be opened here, and I think >> it may be better to see the pjsua log file, as the patch would print >> some warning message regarding the issue in the log file. >> >> BR, >> nanang >> >> >> On Fri, Oct 23, 2009 at 12:28 PM, Bharat Yadav >> <bharat.yadav@axisconvergence.com> wrote: >>> Dear Nanang >>> I tested Session timer fix with revision svn 2961 but still having same > as >>> before. Wireshark trace attached.(forget to attach file now with this > one) >>> Thanks and regards >>> Bharat Yadav >>> >>> -----Original Message----- >>> From: pjsip-bounces@lists.pjsip.org > [mailto:pjsip-bounces@lists.pjsip.org] >>> On Behalf Of Nanang Izzuddin >>> Sent: Thursday, October 15, 2009 10:15 AM >>> To: pjsip list >>> Subject: Re: [pjsip] Session Timer Too Small >>> >>> Hi Bharat, >>> >>> Just want to update you regarding this issue. There was update on >>> ticket #954, i.e: rev 2933-2934, to handle this case. >>> >>> Please drop in any feedback once you've got a chance to test it, thanks. >>> >>> BR, >>> nanang >>> >>> >>> On Fri, Aug 21, 2009 at 10:28 PM, Nanang Izzuddin <nanang@pjsip.org> >> wrote: >>>> Hi Bharat, >>>> >>>> The log does help. The UAS said in its 422/INVITE response that Min-SE >>>> is 5400, but then UAS sent SE 3600 in its 200/INVITE response. The >>>> symbian_ua/PJSIP doesn't like it when the 200/INVITE response contains >>>> Session-expires header with value less than Min-SE header in INVITE >>>> request, so BYE was sent. >>>> >>>> The faulty UA here is the UAS, take a look at RFC 4028 Section 9: >>>> === >>>> If the UAS wishes to accept the request, it copies the value of the >>>> Session-Expires header field from the request into the 2xx response. >>>> The UAS response MAY reduce its value but MUST NOT set it to a >>>> duration lower than the value in the Min-SE header field in the >>>> request, if it is present; >>>> === >>>> >>>> However, I've just created ticket #954 (Session Timer issues) and >>>> considered to put this case in. >>>> >>>> Thanks for the report, >>>> nanang >>>> >>>> >>>> On Fri, Aug 21, 2009 at 7:04 PM, Bharat >>>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>>> Dear Nanang >>>>> Here is trace logs of symbian_ua and Wireshark. >>>>> Thanks and regards >>>>> Bharat >>>>> >>>>> -----Original Message----- >>>>> From: pjsip-bounces@lists.pjsip.org >>> [mailto:pjsip-bounces@lists.pjsip.org] >>>>> On Behalf Of Bharat Yadav >>>>> Sent: Friday, August 21, 2009 5:10 PM >>>>> To: 'pjsip list' >>>>> Subject: Re: [pjsip] Session Timer Too Small >>>>> >>>>> Dear Nanang >>>>> Thanks for quick reply. First of all when I want to make call with G711 >>> it >>>>> will ok and call get connected and I hangup the call gracefully, but if >> I >>>>> only use G729 for that case when call made at the stage of Ringing if >>>>> recipient accept the call it shows "Session Timer Too small" and get >>> hanged >>>>> with "normal call clearing" message. From the log end with will send > the >>> log >>>>> file within as while. >>>>> Thanks >>>>> Bharat >>>>> >>>>> -----Original Message----- >>>>> From: pjsip-bounces@lists.pjsip.org >>> [mailto:pjsip-bounces@lists.pjsip.org] >>>>> On Behalf Of Nanang Izzuddin >>>>> Sent: Friday, August 21, 2009 4:52 PM >>>>> To: pjsip list >>>>> Subject: Re: [pjsip] Session Timer Too Small >>>>> >>>>> Hi Bharat, >>>>> >>>>> I don't think I get this right. There shouldn't be a problem when a >>>>> caller gets 422 response (session timer too small), it will just >>>>> re-try to send INVITE with acceptable session interval as specified by >>>>> the 422 response automatically (no config setting to be set/modified >>>>> here). >>>>> >>>>> So, did you experience other than the above scenario? Log file or >>>>> clear reproducing steps could be helpful. >>>>> >>>>> Regards, >>>>> nanang >>>>> >>>>> >>>>> On Fri, Aug 21, 2009 at 5:24 PM, Bharat >>>>> Yadav<bharat.yadav@axisconvergence.com> wrote: >>>>>> Hi all >>>>>> >>>>>> I am using 1.4 trunk and trying to implement VAS for FP1 using >>> symbian_ua >>>>>> all are fine for Ringing stage when call connect to GSM phone using >> G729 >>>>> it >>>>>> show "Session Timer Too Small", how should and where I define session >>> time >>>>>> into ua.cpp, I checked into pjsua_app.c but failed to follow steps for >>>>>> session timer expression. Please help. >>>>>> >>>>>> Thanks >>>>>> >>>>>> Bharat >>>>>> >>>>>> _______________________________________________ >>>>>> Visit our blog: http://blog.pjsip.org >>>>>> >>>>>> pjsip mailing list >>>>>> pjsip@lists.pjsip.org >>>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>>> >>>>>> >>>>> >>>>> _______________________________________________ >>>>> Visit our blog: http://blog.pjsip.org >>>>> >>>>> pjsip mailing list >>>>> pjsip@lists.pjsip.org >>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> Visit our blog: http://blog.pjsip.org >>>>> >>>>> pjsip mailing list >>>>> pjsip@lists.pjsip.org >>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>> >>>>> >>>>> _______________________________________________ >>>>> Visit our blog: http://blog.pjsip.org >>>>> >>>>> pjsip mailing list >>>>> pjsip@lists.pjsip.org >>>>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>>>> >>>>> >>>> >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> _______________________________________________ >>> Visit our blog: http://blog.pjsip.org >>> >>> pjsip mailing list >>> pjsip@lists.pjsip.org >>> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >>> >>> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> >> >> _______________________________________________ >> Visit our blog: http://blog.pjsip.org >> >> pjsip mailing list >> pjsip@lists.pjsip.org >> http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org >> > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > > _______________________________________________ > Visit our blog: http://blog.pjsip.org > > pjsip mailing list > pjsip@lists.pjsip.org > http://lists.pjsip.org/mailman/listinfo/pjsip_lists.pjsip.org > >