Thanks Abdul This comes as a pretty big blow, as this is what I was hoping to do with it from the start. Is there a way to set it up to read one address continuously? thanks in advance-Patrick Prologix wrote: > Patrick, > > Prologix GPIB-USB controller does not work as a GPIB bus sniffer. In DEVICE > mode the controller reads the bus only if it has previously been addressed > as a listener. > > Regards, > Abdul > > > -----Original Message----- > From: time-nuts-bounces@febo.com [mailto:time-nuts-bounces@febo.com] On > Behalf Of Patrick > Sent: Sunday, January 27, 2008 10:25 AM > To: Discussion of precise time and frequency measurement > Subject: [time-nuts] prologix device as sniffer > > Hi Everyone > > Thanks to all for helping me with my last post. I am now reading with my > Prologix device. > > I am just not sure that I am reading everything. I am trying to monitor > the communication between a closed source App and some GPIB devices. > > After I set up imported and set up serial with PySerial I tried this: > > ser.write("++mode0\r\n") > > x=1 > > def read3(): > while(x==1): > print ser.read(1000) > > I also tried print ser.readline() > > I read the "ID" command sent out by the software but I could not read > the response. Am I reading all the addresses with this set up or just > one? Does anyone have some thoughts on why I don't read the response? > > Thanks yet again in advance-patrick > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > >

Patrick, Sorry the product didn't work out for you. With the current firmware, there is really no good way to do what you want to do. GPIB bus sniffing is an oft-requested feature that we will certainly consider adding in the future. Email me off-line if you wish to return the unit. Regards, Abdul -----Original Message----- From: time-nuts-bounces@febo.com [mailto:time-nuts-bounces@febo.com] On Behalf Of Patrick Sent: Sunday, January 27, 2008 11:41 AM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] prologix device as sniffer Thanks Abdul This comes as a pretty big blow, as this is what I was hoping to do with it from the start. Is there a way to set it up to read one address continuously? thanks in advance-Patrick Prologix wrote: > Patrick, > > Prologix GPIB-USB controller does not work as a GPIB bus sniffer. In DEVICE > mode the controller reads the bus only if it has previously been addressed > as a listener. > > Regards, > Abdul > > > -----Original Message----- > From: time-nuts-bounces@febo.com [mailto:time-nuts-bounces@febo.com] On > Behalf Of Patrick > Sent: Sunday, January 27, 2008 10:25 AM > To: Discussion of precise time and frequency measurement > Subject: [time-nuts] prologix device as sniffer > > Hi Everyone > > Thanks to all for helping me with my last post. I am now reading with my > Prologix device. > > I am just not sure that I am reading everything. I am trying to monitor > the communication between a closed source App and some GPIB devices. > > After I set up imported and set up serial with PySerial I tried this: > > ser.write("++mode0\r\n") > > x=1 > > def read3(): > while(x==1): > print ser.read(1000) > > I also tried print ser.readline() > > I read the "ID" command sent out by the software but I could not read > the response. Am I reading all the addresses with this set up or just > one? Does anyone have some thoughts on why I don't read the response? > > Thanks yet again in advance-patrick > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.