Search results for all lists

10000 messages found
Sort by
List: time-nuts@lists.febo.com
From: paul swed
 
Re: [time-nuts] Thunderbolt question
Fri, Aug 4, 2017 10:10 PM
In the photo of the > top of the board the signal comes into a filter then to a 25db amp > marked AM50002 by Macom. Above the filter near the input is where the > decoupled +5VDC for the antenna is connected. If you are only reading > 0.5VDC, if your're lucky it might only be the amp is fried and that > could be an easy fix.
List: volt-nuts@lists.febo.com
From: J. L. Trantham
 
Re: [volt-nuts] Solartron 7081 .. what to look for
Fri, Mar 11, 2016 3:40 AM
Easy to test to make sure I'm correct. Just remove the wires from the switch (they slide off) and measure to see if it is 'open' or 'closed'. There are a couple of batteries (at least one) that might need to be replaced. Easy to measure the voltage and see the date code. Needed for keeping the 'state' but not the Cal constants, IIRC.
List: discuss@lists.openscad.org
From: Doug Moen
 
Re: [OpenSCAD] Userspace extensibility of core modules, and minimalist OpenSCAD
Mon, Dec 28, 2020 7:01 PM
Unlike the bizarre hack concern above, I think >> if it was easy to extend the core then people would be proposing all sorts >> of changes. I think it makes more sense to keep things as they are and >> allow libraries to extend the core (as is already basically possible).
List: tacomaart@list.cityoftacoma.org
From: Jackie
 
Creative Colloquy Crawl
Sat, Sep 30, 2017 12:23 AM
All Ages > > Songs and the Stories They Tell – The Other Side of the Coin: 8 PM-Harmon Taproom ~Inspired by the many music podcasts that merge the interview format with live performance, singer songwriter Travis Barker will be performing songs that have a story, including many from his forthcoming album.
List: discuss@lists.openscad.org
From: Adrian Mariano
 
Re: How to round the top inner and outer edges?
Wed, Sep 6, 2023 11:23 PM
I think it has been requested >>> before and all the 2D geometry modules are fast enough to be functions and >>> I can't see any downsides.
List: trawlers@lists.trawlering.com
From: Ken Phelps
 
Re: TWL: Bernoulli effect is not why wings fly
Fri, Aug 15, 2003 6:12 PM
This means the air >passing over the top has to travel further to arrive at the trailing edge so >it travels faster and the reduced pressure creates a SUCTION on top of the >wing. > >And I did stay in a Holiday Inn last night. > >Andina Foster, >tech@yandina.com > So how did all those model planes with wings of perfectly flat balsa (with a shallow angle of
List: usrp-users@lists.ettus.com
From: xi yang
 
Re: [USRP-users] FPGA testbench
Tue, Jan 3, 2012 9:55 AM
Hi, All, Have found most modules in different folders except ../top/USRP2/u2_core.v:337: error: Unknown module type: zpu_wb_top There is a zpu_wb_top.vhd under opencores/zpu, but it is a .vhd instead of .v How to get around it? How to get through errors like ../models/FIFO_GENERATOR_V6_1.v:1194: sorry: Constant user functions are not yet supported. ..
List: trawlers@lists.trawlering.com
From: Richard Cook
 
Re: T&T: Soldering Battery terminals
Mon, Nov 3, 2014 5:20 PM
I read MaineSail's writeup, bought the recommended FTZ crimper and all new top quality lugs, correctly sized to match the cable and posts they were used on, and carefully re-did all ends per his instructions. It was relatively easy, and I'm pretty sure now that they were done in a superior manner. BTW the engine starts very well now.
List: tacomaart@list.cityoftacoma.org
From: Lynn Di Nino
 
The news is out, all over town
Mon, Aug 16, 2010 10:26 PM
All three galleries invite you to this preview at the same location: A is Mineral, B is "Don't Look" and C is the Val Persoon Gallery featuring watercolor. Mineral, and Val Persoon Gallery open Thursday, August 19 from 5-8 pm, 301 Puyallup Avenue.
List: trawlers@lists.trawlering.com
From: Walter Konieczko
 
Re: T&T: list for all subscribers
Thu, Jan 10, 2008 1:23 AM
Walt Konieczko Annie Sez Too 34 Maine Trader (with Onan MDJE) Lanoka Harbor, NJ > > Hi all.. > ?? need help with an old Onan 7.5-MDJE-3CR, it wont shut down with the > off > switches, niether the remote panel or the onboard, i have to > manually?push the > lever on the injection?