Hi,
Guest
Search results for all lists
List: trawlers@lists.trawlering.com
From: James Millar
Corroseal Rust Converter (was Ospho rust killer)
Mon, Apr 3, 2017 2:10 PM
Once again I am trying it on the top and sides of my steel fuel tanks.. the tops of the tanks had medium to light rust with little evidence of the original paint; while the sides had a few rust spots but most of the original paint.
List: trawlers@lists.trawlering.com
From: Milt Baker
Re: T&T: Onboard vs on board
Wed, Dec 4, 2019 12:13 AM
Milt Baker, Nordhavn 47 Bluewater
-----
- top definitions
top-definitions-section>
- examples
- explore dictionary
List: discuss@lists.openscad.org
From: nop head
Re: [OpenSCAD] Unnecessary triangulation in linear_extrude
Sun, Jan 3, 2016 9:01 PM
I guess removing the hole in the top removes a
> trip through CGAL and the circle coordinates remain exactly equal.
List: discuss@lists.openscad.org
From: Ronaldo Persiano
Re: [OpenSCAD] Polyhedron tube with irregular sides -- is it possible ?
Tue, Jan 15, 2019 3:31 AM
[18, 17, 20, 21], [16, 18, 21, 19]];
The following image of the polyhedron(pts, faces) enhances the top and
bottom partition:
[image: polyWithHoles.PNG]
Intentionally the top and bottom partitions are differents.
List: usrp-users@lists.ettus.com
From: Ian Buckley
Re: [USRP-users] .bin make issues
Thu, Jun 18, 2015 5:57 PM
Usrp3/top instead of usrp2/top, but I have no top
> > > files through either of those file paths do it didn't matter anyways.
> > >
> > > I believe the apt-get command were through my not reading completely.
> > > Those were for the UHD code.
> > >
> > > ISE is properly installed without any issues.
> >
> > Great, then you're all set!
List: usrp-users@lists.ettus.com
From: André Gomes
Re: [USRP-users] Error during synthesis
Mon, Dec 4, 2017 9:24 PM
: not found
> build-B210//b200.xise
> xtclsh /opt/uhd/fpga-src/usrp3/top/tcl/ise_helper.tcl ""
> /bin/sh: 1: xtclsh: not found
> ..
List: time-nuts@lists.febo.com
From: Chuck Harris
Re: [time-nuts] Terrestrial Tides and Land Movement
Tue, May 26, 2015 12:39 PM
If you do a good job of sealing the
connector (eg. lots of wraps of electrical tape, followed by
a few of friction tape) there in no intrinsic reason you couldn't
safely mount yours on top of the main plumbing vent stack.
List: discuss@lists.openscad.org
From: (null) (null)
Re: How can I scale() right with linear_extrude() ?
Mon, Apr 5, 2021 1:51 AM
>
> You've got it set up so that the top and bottom are the same size in Y, but the top is smaller in X. That's what the "scale=[0.11, 1]" means.
>
> Is the bottom of this object the shape that you want, a hollow rectangle with outside dimensions [7, 3] and inside dimensions [6.5, 2.5]?
List: discuss@lists.openscad.org
From: Jordan Brown
Re: Module Disappears In Render
Fri, Sep 3, 2021 6:00 PM
All of the top Z values would have been calculated using the
same numbers, as would all of the bottom Z values. Those top Z values
would either all be the same as the bottom Z values of the next layer,
or would all be different. In either case, you're OK.
List: discuss@lists.openscad.org
From: Leonard Martin Struttmann
Re: Using BOSL2 and getting the thread "depth" to match.
Mon, Aug 9, 2021 4:56 PM
.
>>
>> I'm having trouble getting my thread "depth" to match up I'm trying to
>> get it to be *2.16mm* (*#4*) but when measured (Using Blender it's
>> *1.25mm*)
>>
>> Here's my process:
>>
>> Measure Original bottle top:
>> 1) Measure OUTSIDE of bottle top (no Threads)
>> * 39.34mm*
>> 2) Measure OUTSIDE of Bottle top (include all Threads)
>> *41.5mm