[USRP-users] Building RFNoC Image with OOT Module on X310 - Module not found
ejkreinar at gmail.com
Sat Jan 4 16:20:46 EST 2020
It's tough to debug your specific issues without seeing the whole OOT repo
structure, including makefiles, etc.
However I regularly use rfnoc with OOT folders successfully and have an
example here you might be able to refer to for some hints:
I might suggest trying to check that out and see if you can build with one
of those blocks first, then modify for your purposes?
Also, one other thing to mention is you might have some luck debugging the
uhd_image_builder.py to see where it's going wrong in your case (it's just
a python file so it's pretty easy to add debug markers or print statements
if you want)...
On Sat, Jan 4, 2020, 5:10 AM Felix Greiwe via USRP-users <
usrp-users at lists.ettus.com> wrote:
> Hello again,
> has no one an idea? I have still not managed to get it working..
> I would take any advice!
> Best regards,
> > Hello together,
> > recently I installed the whole UHD/GNU-Radio Toolchain on a fresh install
> > of Kubuntu 18.04 LTS. I followed the instructions from
> > https://kb.ettus.com/Getting_Started_with_RFNoC_Development
> > and used the Pybombs install.
> > (I ran into a lot of problems there and had to install a lot of stuff
> > manually because most of the commands were not working properly. Maybe
> > Pybombs Tutorial Section needs an update?)
> > Finally I managed to install it successfully and the command
> > uhd_config_version -- info prints: UHD 22.214.171.124-124-geb448043
> > (I also installed Vivado 2018.3 and added the License which seems to
> > work.)
> > After the install I wanted to validate it by creating an OOT Module and
> > OOT Block named noc_block_checkdevprocess.v. I did not edit the Verilog
> > Code because I only wanted to know if I was able to build an Image
> > properly.
> > (I ran the default Testbench too, which worked without errors.)
> > The command to build my image is:
> > ./uhd_image_builder.py checkdevprocess digital_gain -t X310_RFNOC_HG -d
> > X310 -I /home/lskt/rfnoc-blocks_lskt/rfnoc
> > with "rfnoc-blocks_lskt" beeing my OOT Module and "checkdevprocess"
> > my custom block.
> > (I also tried the paths home/lskt/rfnoc-blocks_lskt/rfnoc/;
> > home/lskt/rfnoc-blocks_lskt/; home/lskt/rfnoc-blocks_lskt/rfnoc/fpga-src
> > Every single time I get the same error message:
> > ERROR: [Synth 8-439] module 'noc_block_checkdevprocess' not found
> > and I don't know why.
> > I also tried the the uhd_image_builder_gui.py which did not even pop up
> > until I uncommented the Line at row 149. I can see my OOT Block here
> > adding the Module in the gui, but it prints the same error message as the
> > non-gui version.
> > If you need further information to help please ask.
> > Any help is appreciated.
> > Felix
> > _______________________________________________
> > USRP-users mailing list
> > USRP-users at lists.ettus.com
> > http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
> USRP-users mailing list
> USRP-users at lists.ettus.com
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the USRP-users