[USRP-users] X310 unable to connect after recovery procedure

Nicolas GALLAND nicolas.galland at obspm.fr
Thu Mar 28 07:26:03 EDT 2019


Hi,

I used the file named usrp_x310_fpga_HG.bit

Nicolas


Le 27/03/2019 à 15:10, Marcus D. Leech a écrit :
> On 03/27/2019 05:39 AM, Nicolas GALLAND wrote:
>> Hi,
>>
>> after the recovery, i can't ping the device to the default address. 
>> It gives me a "host unreachable" error when I try.
>>
>> Nicolas
> Which image did you select when you used Vivado to recover the device 
> via JTAG?
>
>
>>
>> Le 26/03/2019 à 17:28, Marcus D Leech a écrit :
>>> So it’s not clear where we are at here.
>>>
>>> After recovery can you ping the device at the default address?
>>>
>>>
>>>
>>> Sent from my iPhone
>>>
>>>> On Mar 25, 2019, at 12:12 PM, Joe Martin via USRP-users 
>>>> <usrp-users at lists.ettus.com> wrote:
>>>>
>>>> Thanks, Nicolas.  I am interested to hear how you eventually clear 
>>>> the problem as I also have an X310 and so far all works fine but 
>>>> someday I may face the same issue as you are experiencing so please 
>>>> when you find a solution please post it.  I am not experienced 
>>>> enough yet with mine to be able to suggest a solution for you 
>>>> unfortunately.  Maybe someone else can.
>>>>
>>>> I (like you) am eager to hear any suggestion(s) to resolve your issue.
>>>>
>>>> Regards,
>>>>
>>>> Joe
>>>>
>>>>> On Mar 25, 2019, at 9:28 AM, Nicolas GALLAND 
>>>>> <nicolas.galland at obspm.fr> wrote:
>>>>>
>>>>> Hi,
>>>>>
>>>>> it is indeed a typo here. I did ping 192.168.10.2 first, and then 
>>>>> I tried on 192.168.10.3 to see if the error message was the same. 
>>>>> In any case (even using ping broadcast on all the sub network my 
>>>>> computer is connected to) i have this message. It looks like there 
>>>>> is a connection between the computer and the device, since my 
>>>>> computer says there is no more network when I switch off the USRP.
>>>>>
>>>>> Kind regards
>>>>>
>>>>> Nicolas
>>>>>> Le 22/03/2019 à 18:52, Joe Martin a écrit :
>>>>>> Nicolas,
>>>>>>
>>>>>> It appears you were pinging 192.168.10.3, not 192.168.10.2.  
>>>>>> Maybe this particular example was simply a typo and you used the 
>>>>>> correct IP address to ping during your other tests?
>>>>>>
>>>>>> Regards,
>>>>>>
>>>>>> Joe
>>>>>>
>>>>>>> On Mar 22, 2019, at 11:05 AM, Nicolas GALLAND via USRP-users 
>>>>>>> <usrp-users at lists.ettus.com> wrote:
>>>>>>>
>>>>>>> Hello everyone,
>>>>>>>
>>>>>>> I had some trouble with my X310 and I needed to upload my UHD 
>>>>>>> installation and consequently to update the FPGA image on the 
>>>>>>> board. After doing it through eternet port, I lost connection so 
>>>>>>> I decide to follow the recovery procedure to upload the FPGA 
>>>>>>> image using the JTAG port (following 
>>>>>>> https://kb.ettus.com/X300/X310_Device_Recovery).
>>>>>>>
>>>>>>> The upload is fine, and the computer recognises the network with 
>>>>>>> IP address 192.168.10.1, but when I try to ping 192.168.10.2 (as 
>>>>>>> explained in the procedure) I have
>>>>>>>
>>>>>>> PING 192.168.10.3 (192.168.10.3) 56(84) bytes of data.
>>>>>>>  From 192.168.10.1 icmp_seq=1 Destination Host Unreachable
>>>>>>>  From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
>>>>>>>  From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
>>>>>>>  From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
>>>>>>>  From 192.168.10.1 icmp_seq=5 Destination Host Unreachable
>>>>>>>
>>>>>>> until I stop it. I have two x310 in the same situation, and I 
>>>>>>> tried on two different computers with different ethernet cables.
>>>>>>>
>>>>>>> Could the hardware be broken ? (If so, isn't it strange that the 
>>>>>>> computer still sees the network ?)
>>>>>>>
>>>>>>> Thanks a lot, and nice week end !
>>>>>>>
>>>>>>> Kind regards,
>>>>>>>
>>>>>>>     Nicolas
>>>>>>>
>>>>
>>>> _______________________________________________
>>>> USRP-users mailing list
>>>> USRP-users at lists.ettus.com
>>>> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
>



More information about the USRP-users mailing list