[USRP-users] Standalone signal generator on B205mini

Justo Ramos, Diego djusto at indra.es
Thu Mar 28 06:07:54 EDT 2019


Hello Ian,

I want a continuous TX  of a generated signal, because I want to use the USB exclusively for RX. I don't know if I can configure by UHD this option at first time, without sending data all time and modifying the input TX data of the b205_io block with my desired signal. Is this option of configuration possible? I think that with that option I could accomplish the 3 tips that you wrote.

Thanks for your answer.

Regards,
Diego

De: Ian Buckley <ianb at ionconcepts.com>
Enviado el: Wednesday, March 27, 2019 4:50 AM
Para: Justo Ramos, Diego <djusto at indra.es>
CC: usrp-users <usrp-users at lists.ettus.com>
Asunto: Re: [USRP-users] Standalone signal generator on B205mini

I can’t give you a specific solution Diego because there are a lot of things here that *could* be the issue.
However in general my tips for hacking fast custom B2xx FPGA images are:
1) Do it in such a way that UHD can not tell you changed the FPGA.
i.e All register transactions should work as expected from the perspective of UHD (Understand though it doesn’t “know” if the transaction did what it expected, only that it got an acknowledgement)
If you want to transmit then still send a sample stream to the USRP even if you discard it after it is acknowledged by the USRP (It can be a much lower sample rate than your custom logic outputs, you control radio_clk directly with master_clock_rate, sample rate controls the interpolation ratio down from radio_clk)
2) Use the driver functionality of UHD to control all the H/W. Really you don’t want to debug driver style code if you are in a hurry, especially the transceiver.
3) Don't touch the logic that interfaces immediately to the FPGA pins so as too preserve off-chip timing…a lot of work went into qualifying that.
-Ian

On Mar 26, 2019, at 10:07 AM, Justo Ramos, Diego via USRP-users <usrp-users at lists.ettus.com<mailto:usrp-users at lists.ettus.com>> wrote:

Hello all,

I have an B205mini board and I'm interested in modifying the internal TX block of the FPGA, to be an standalone signal generator.

I created a custom block that generates a signal, in this case a pulse generator, with the two components of 12 bits for I and Q. Then I connect these two components into  b205_io's tx_i0 y rx_i0. I use the radio_clk as clock to generate samples of the signal.

Finally I remake the binary files of the FPGA and I reprogram the B205mini, but when I use the Spectrum Analyzer I don't have any signal  on the TX frequency.

I don't know if I have to change the clock for generation of samples or activate another signal. Could someone give me an advice to achieve custom transmission from the FPGA?

Thanks you.

Best regards,
Diego

________________________________

Este correo electrónico y, en su caso, cualquier fichero anexo al mismo, contiene información de carácter confidencial exclusivamente dirigida a su destinatario o destinatarios. Si no es vd. el destinatario indicado, queda notificado que la lectura, utilización, divulgación y/o copia sin autorización está prohibida en virtud de la legislación vigente. En el caso de haber recibido este correo electrónico por error, se ruega notificar inmediatamente esta circunstancia mediante reenvío a la dirección electrónica del remitente.
Evite imprimir este mensaje si no es estrictamente necesario.

This email and any file attached to it (when applicable) contain(s) confidential information that is exclusively addressed to its recipient(s). If you are not the indicated recipient, you are informed that reading, using, disseminating and/or copying it without authorisation is forbidden in accordance with the legislation in effect. If you have received this email by mistake, please immediately notify the sender of the situation by resending it to their email address.
Avoid printing this message if it is not absolutely necessary.
_______________________________________________
USRP-users mailing list
USRP-users at lists.ettus.com<mailto:USRP-users at lists.ettus.com>
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com


________________________________

Este correo electrónico y, en su caso, cualquier fichero anexo al mismo, contiene información de carácter confidencial exclusivamente dirigida a su destinatario o destinatarios. Si no es vd. el destinatario indicado, queda notificado que la lectura, utilización, divulgación y/o copia sin autorización está prohibida en virtud de la legislación vigente. En el caso de haber recibido este correo electrónico por error, se ruega notificar inmediatamente esta circunstancia mediante reenvío a la dirección electrónica del remitente.
Evite imprimir este mensaje si no es estrictamente necesario.

This email and any file attached to it (when applicable) contain(s) confidential information that is exclusively addressed to its recipient(s). If you are not the indicated recipient, you are informed that reading, using, disseminating and/or copying it without authorisation is forbidden in accordance with the legislation in effect. If you have received this email by mistake, please immediately notify the sender of the situation by resending it to their email address.
Avoid printing this message if it is not absolutely necessary.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/attachments/20190328/584eb7ce/attachment.html>


More information about the USRP-users mailing list