[USRP-users] X310 unable to connect after recovery procedure

Marcus D. Leech patchvonbraun at gmail.com
Wed Mar 27 10:10:42 EDT 2019


On 03/27/2019 05:39 AM, Nicolas GALLAND wrote:
> Hi,
>
> after the recovery, i can't ping the device to the default address. It 
> gives me a "host unreachable" error when I try.
>
> Nicolas
Which image did you select when you used Vivado to recover the device 
via JTAG?


>
> Le 26/03/2019 à 17:28, Marcus D Leech a écrit :
>> So it’s not clear where we are at here.
>>
>> After recovery can you ping the device at the default address?
>>
>>
>>
>> Sent from my iPhone
>>
>>> On Mar 25, 2019, at 12:12 PM, Joe Martin via USRP-users 
>>> <usrp-users at lists.ettus.com> wrote:
>>>
>>> Thanks, Nicolas.  I am interested to hear how you eventually clear 
>>> the problem as I also have an X310 and so far all works fine but 
>>> someday I may face the same issue as you are experiencing so please 
>>> when you find a solution please post it.  I am not experienced 
>>> enough yet with mine to be able to suggest a solution for you 
>>> unfortunately.  Maybe someone else can.
>>>
>>> I (like you) am eager to hear any suggestion(s) to resolve your issue.
>>>
>>> Regards,
>>>
>>> Joe
>>>
>>>> On Mar 25, 2019, at 9:28 AM, Nicolas GALLAND 
>>>> <nicolas.galland at obspm.fr> wrote:
>>>>
>>>> Hi,
>>>>
>>>> it is indeed a typo here. I did ping 192.168.10.2 first, and then I 
>>>> tried on 192.168.10.3 to see if the error message was the same. In 
>>>> any case (even using ping broadcast on all the sub network my 
>>>> computer is connected to) i have this message. It looks like there 
>>>> is a connection between the computer and the device, since my 
>>>> computer says there is no more network when I switch off the USRP.
>>>>
>>>> Kind regards
>>>>
>>>> Nicolas
>>>>> Le 22/03/2019 à 18:52, Joe Martin a écrit :
>>>>> Nicolas,
>>>>>
>>>>> It appears you were pinging 192.168.10.3, not 192.168.10.2.  Maybe 
>>>>> this particular example was simply a typo and you used the correct 
>>>>> IP address to ping during your other tests?
>>>>>
>>>>> Regards,
>>>>>
>>>>> Joe
>>>>>
>>>>>> On Mar 22, 2019, at 11:05 AM, Nicolas GALLAND via USRP-users 
>>>>>> <usrp-users at lists.ettus.com> wrote:
>>>>>>
>>>>>> Hello everyone,
>>>>>>
>>>>>> I had some trouble with my X310 and I needed to upload my UHD 
>>>>>> installation and consequently to update the FPGA image on the 
>>>>>> board. After doing it through eternet port, I lost connection so 
>>>>>> I decide to follow the recovery procedure to upload the FPGA 
>>>>>> image using the JTAG port (following 
>>>>>> https://kb.ettus.com/X300/X310_Device_Recovery).
>>>>>>
>>>>>> The upload is fine, and the computer recognises the network with 
>>>>>> IP address 192.168.10.1, but when I try to ping 192.168.10.2 (as 
>>>>>> explained in the procedure) I have
>>>>>>
>>>>>> PING 192.168.10.3 (192.168.10.3) 56(84) bytes of data.
>>>>>>  From 192.168.10.1 icmp_seq=1 Destination Host Unreachable
>>>>>>  From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
>>>>>>  From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
>>>>>>  From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
>>>>>>  From 192.168.10.1 icmp_seq=5 Destination Host Unreachable
>>>>>>
>>>>>> until I stop it. I have two x310 in the same situation, and I 
>>>>>> tried on two different computers with different ethernet cables.
>>>>>>
>>>>>> Could the hardware be broken ? (If so, isn't it strange that the 
>>>>>> computer still sees the network ?)
>>>>>>
>>>>>> Thanks a lot, and nice week end !
>>>>>>
>>>>>> Kind regards,
>>>>>>
>>>>>>     Nicolas
>>>>>>
>>>
>>> _______________________________________________
>>> USRP-users mailing list
>>> USRP-users at lists.ettus.com
>>> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com




More information about the USRP-users mailing list