[USRP-users] X310 unable to connect after recovery procedure

Marcus D Leech patchvonbraun at gmail.com
Tue Mar 26 12:28:47 EDT 2019


So it’s not clear where we are at here. 

After recovery can you ping the device at the default address?



Sent from my iPhone

> On Mar 25, 2019, at 12:12 PM, Joe Martin via USRP-users <usrp-users at lists.ettus.com> wrote:
> 
> Thanks, Nicolas.  I am interested to hear how you eventually clear the problem as I also have an X310 and so far all works fine but someday I may face the same issue as you are experiencing so please when you find a solution please post it.  I am not experienced enough yet with mine to be able to suggest a solution for you unfortunately.  Maybe someone else can. 
> 
> I (like you) am eager to hear any suggestion(s) to resolve your issue.
> 
> Regards, 
> 
> Joe
> 
>> On Mar 25, 2019, at 9:28 AM, Nicolas GALLAND <nicolas.galland at obspm.fr> wrote:
>> 
>> Hi,
>> 
>> it is indeed a typo here. I did ping 192.168.10.2 first, and then I tried on 192.168.10.3 to see if the error message was the same. In any case (even using ping broadcast on all the sub network my computer is connected to) i have this message. It looks like there is a connection between the computer and the device, since my computer says there is no more network when I switch off the USRP.
>> 
>> Kind regards
>> 
>> Nicolas
>>> Le 22/03/2019 à 18:52, Joe Martin a écrit :
>>> Nicolas,
>>> 
>>> It appears you were pinging 192.168.10.3, not 192.168.10.2.  Maybe this particular example was simply a typo and you used the correct IP address to ping during your other tests?
>>> 
>>> Regards,
>>> 
>>> Joe
>>> 
>>>> On Mar 22, 2019, at 11:05 AM, Nicolas GALLAND via USRP-users <usrp-users at lists.ettus.com> wrote:
>>>> 
>>>> Hello everyone,
>>>> 
>>>> I had some trouble with my X310 and I needed to upload my UHD installation and consequently to update the FPGA image on the board. After doing it through eternet port, I lost connection so I decide to follow the recovery procedure to upload the FPGA image using the JTAG port (following https://kb.ettus.com/X300/X310_Device_Recovery).
>>>> 
>>>> The upload is fine, and the computer recognises the network with IP address 192.168.10.1, but when I try to ping 192.168.10.2 (as explained in the procedure) I have
>>>> 
>>>> PING 192.168.10.3 (192.168.10.3) 56(84) bytes of data.
>>>> From 192.168.10.1 icmp_seq=1 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
>>>> From 192.168.10.1 icmp_seq=5 Destination Host Unreachable
>>>> 
>>>> until I stop it. I have two x310 in the same situation, and I tried on two different computers with different ethernet cables.
>>>> 
>>>> Could the hardware be broken ? (If so, isn't it strange that the computer still sees the network ?)
>>>> 
>>>> Thanks a lot, and nice week end !
>>>> 
>>>> Kind regards,
>>>> 
>>>>    Nicolas
>>>> 
>> 
> 
> 
> _______________________________________________
> USRP-users mailing list
> USRP-users at lists.ettus.com
> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com



More information about the USRP-users mailing list