[USRP-users] rfnoc blocks with multiple inputs/outputs

Dario Pennisi dario at iptronix.com
Fri Oct 13 15:38:28 EDT 2017


Hi Mike,
Unfortunately what you write is not what I see. Split stream has 1 input and 2 outputs and that works. What I am saying is that the opposite doesn't. This seems to be due to the fact that for some reason blocks feeding second input are not started if block does not have a second port.
With the same block, even without adding code for a second output but just adding the fake output to the block descriptors made it work...
I'm sure there's a bug somewhere in uhd or gr-ettus as he is fine.
Best regards,

Dario Pennisi








On Fri, Oct 13, 2017 at 9:32 PM +0200, "Michael West" <michael.west at ettus.com<mailto:michael.west at ettus.com>> wrote:

Hi Dario,

A block can have any number of inputs and outputs, so 2 inputs and 1 output is fine.  The Split Stream block is an example of an asymmetric block.

The UHD XML description of the Split Stream block can be found here:  https://github.com/EttusResearch/uhd/blob/rfnoc-devel/host/include/uhd/rfnoc/blocks/splitstream.xml
The GnuRadio XML description of the Split Stream block can be found here:  https://github.com/EttusResearch/gr-ettus/blob/master/grc/uhd_rfnoc_split_stream.xml

Hopefully, those examples will help.

As far as the multiple ports at 200 Msps on a single block, it is a known issue.  The bus clock would need to be raised to the CE clock of 214.286 MHz to allow 2 ports to operate at 200 Msps in one block, but doing that causes the FPGA build to fail timing.  As far as a workaround or trick, there is a way where you can hack up the core FPGA code and make a single module with 2 noc_shells connected to separate crossbar ports in the x300_core code, but that is a bit more involved.  If you are daring and curious, look at the way noc_block_axi_dma_fifo and noc_block_radio_core blocks are instantiated and connected to the crossbar in x300_core.v<https://github.com/EttusResearch/fpga/blob/maint/usrp3/top/x300/x300_core.v>.

Regards,
Michael

On Wed, Oct 4, 2017 at 11:57 PM, Dario Pennisi via USRP-users <usrp-users at lists.ettus.com<mailto:usrp-users at lists.ettus.com>> wrote:
Hi,
I am still struggling with a block which should have 2 inputs and 1 output. Apparently everything is fine with both FPGA and software but the second input is not fed with data.
I could not find any example of an asymmetric block with different number of inputs/outputs so I am starting to suspect this is not supported. Can anyone tell me if this is the case and I need to add a dummy output?

Also, when defining block I see that in the xml there is the possibility to specify nports parameter so that a single port definition provides more than one port. If i set nports=2 for the input I am not sure how to define the gnuradio xml descriptor and If I just describe two ports as usual block will not initialize properly.

Finally, I understand that system clock rate on AXI bus is 166 MHz and since NOC ports are 64 bits, on X310 a single block should not be able to process two input streams at 200 MSPS.
Even raising AXI bus clock to 200 MHz would fail as but would still not provide sufficient overhead for packet headers.
Is there any suggested trick to handle this situation? Is it eventually possible to have a single rfnoc block connect to two AXI ports rather than just one?

Thanks,

Dario Pennisi


_______________________________________________
USRP-users mailing list
USRP-users at lists.ettus.com<mailto:USRP-users at lists.ettus.com>
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/attachments/20171013/5ffb5ba2/attachment-0002.html>


More information about the USRP-users mailing list