[USRP-users] Error when burn fpga image file into USRP X310

Nate Temple nate.temple at ettus.com
Fri Jul 14 16:48:17 EDT 2017


Hi Luis,

I will follow up with you on this issue off the list, within the thread that has been sent to support at ettus.com.


Regards,
Nate Temple


> On Jul 14, 2017, at 6:51 AM, Torres Figueroa, Luis Angel via USRP-users <usrp-users at lists.ettus.com> wrote:
> 
> Hi Nate,
>  
> I have exactly the same problem that was reported in previous threads: I loaded a custom FPGA image, got the USRP 2953R (x310) bricked  and then used the JTAG connection with Vivado 2015.4’s Hardware Manager to program the device, however when trying to load an image to flash using the uhd_image_loader command, I get the error: “RuntimeError: Device reported an error during initialization.”
>  
> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2016-December/023092.html
> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2016-October/022064.html
>  
> Could you please let me know which steps must be followed in this case? I attach some logs.
>  
> Best,
> Luis
>  
> ltorresf at pc1:~$ uhd_usrp_probe 
> [INFO] [UHD] linux; GNU C++ version 4.8.4; Boost_105400; UHD_4.0.0.rfnoc-devel-348-g2c2e1a99
> [INFO] [X300] X300 initialization sequence...
> [INFO] [X300] Determining maximum frame size... 
> [INFO] [X300] Maximum frame size: 1472 bytes.
> [INFO] [X300] Setup basic communication...
> [INFO] [X300] Loading values from EEPROM...
> [INFO] [X300] Setup RF frontend clocking...
> [INFO] [X300] Radio 1x clock:200
> [INFO] [X300] Detecting internal GPSDO.... 
> [INFO] [GPS] Found an internal GPSDO: LC_XO, Firmware Rev 0.929a
> [INFO] [RFNOC] [DMA FIFO] Running BIST for FIFO 0... 
> [INFO] [RFNOC] pass (Throughput: 1304.0MB/s)
> [INFO] [RFNOC] [DMA FIFO] Running BIST for FIFO 1... 
> [INFO] [RFNOC] pass (Throughput: 1305.1MB/s)
> [INFO] [RFNOC RADIO] Register loopback test passed
> [INFO] [RFNOC RADIO] Register loopback test passed
> [INFO] [RFNOC RADIO] Register loopback test passed
> [INFO] [RFNOC RADIO] Register loopback test passed
> [WARNING] [RFNOC] [0/fosphor_0] defines 2 input buffer sizes, but 1 input ports
> [INFO] [CORES] Performing timer loopback test... 
> [INFO] [CORES] Timer loopback test passed
> [INFO] [CORES] Performing timer loopback test... 
> [INFO] [CORES] Timer loopback test passed
>   _____________________________________________________
>  /
> |       Device: X-Series Device
> |     _____________________________________________________
> |    /
> |   |       Mboard: X310
> |   |   revision: 6
> |   |   product: 30513
> |   |   mac-addr0: 00:80:2f:0a:ff:b0
> |   |   mac-addr1: 00:80:2f:0a:ff:b1
> |   |   gateway: 192.168.10.1
> |   |   ip-addr0: 192.168.10.3
> |   |   subnet0: 255.255.255.0
> |   |   ip-addr1: 192.168.20.2
> |   |   subnet1: 255.255.255.0
> |   |   ip-addr2: 192.168.30.2
> |   |   subnet2: 255.255.255.0
> |   |   ip-addr3: 192.168.40.2
> |   |   subnet3: 255.255.255.0
> |   |   serial: F5BE96
> |   |   FW Version: 5.1
> |   |   FPGA Version: 33.0
> |   |   FPGA git hash: f764326-dirty
> |   |   RFNoC capable: Yes
> |   |   
> |   |   Time sources:  internal, external, gpsdo
> |   |   Clock sources: internal, external, gpsdo
> |   |   Sensors: gps_gpgga, gps_gprmc, gps_time, gps_locked, gps_servo, ref_locked
> |   |     _____________________________________________________
> |   |    /
> |   |   |       RX Dboard: A
> |   |   |   ID: CBX (0x0067)
> |   |   |   Serial: F58458
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Frontend: 0
> |   |   |   |   Name: CBX RX
> |   |   |   |   Antennas: TX/RX, RX2, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 1200.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
> |   |   |   |   Connection Type: IQ
> |   |   |   |   Uses LO offset: No
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Codec: A
> |   |   |   |   Name: ads62p48
> |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
> |   |     _____________________________________________________
> |   |    /
> |   |   |       RX Dboard: B
> |   |   |   ID: CBX (0x0067)
> |   |   |   Serial: F583B9
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Frontend: 0
> |   |   |   |   Name: CBX RX
> |   |   |   |   Antennas: TX/RX, RX2, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 1200.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
> |   |   |   |   Connection Type: IQ
> |   |   |   |   Uses LO offset: No
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Codec: B
> |   |   |   |   Name: ads62p48
> |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
> |   |     _____________________________________________________
> |   |    /
> |   |   |       TX Dboard: A
> |   |   |   ID: CBX (0x0066)
> |   |   |   Serial: F58458
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Frontend: 0
> |   |   |   |   Name: CBX TX
> |   |   |   |   Antennas: TX/RX, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 1200.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
> |   |   |   |   Connection Type: QI
> |   |   |   |   Uses LO offset: No
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Codec: A
> |   |   |   |   Name: ad9146
> |   |   |   |   Gain Elements: None
> |   |     _____________________________________________________
> |   |    /
> |   |   |       TX Dboard: B
> |   |   |   ID: CBX (0x0066)
> |   |   |   Serial: F583B9
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Frontend: 0
> |   |   |   |   Name: CBX TX
> |   |   |   |   Antennas: TX/RX, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 1200.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
> |   |   |   |   Connection Type: QI
> |   |   |   |   Uses LO offset: No
> |   |   |     _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Codec: B
> |   |   |   |   Name: ad9146
> |   |   |   |   Gain Elements: None
> |   |     _____________________________________________________
> |   |    /
> |   |   |       RFNoC blocks on this device:
> |   |   |   
> |   |   |   * DmaFIFO_0
> |   |   |   * Radio_0
> |   |   |   * Radio_1
> |   |   |   * DDC_0
> |   |   |   * DUC_0
> |   |   |   * FFT_0
> |   |   |   * Window_0
> |   |   |   * FIR_0
> |   |   |   * SigGen_0
> |   |   |   * KeepOneInN_0
> |   |   |   * fosphor_0
> |   |   |   * FIFO_0
> |   |   |   * FIFO_1
>  
> ltorresf at pc1:~$ uhd_find_devices
> [INFO] [UHD] linux; GNU C++ version 4.8.4; Boost_105400; UHD_4.0.0.rfnoc-devel-348-g2c2e1a99
> --------------------------------------------------
> -- UHD Device 0
> --------------------------------------------------
> Device Address:
>     serial: F5BE96
>     addr: 192.168.10.3
>     fpga: HG
>     name: 
>     product: X310
>     type: x300
>  
>  
> ltorresf at pc1:~$ uhd_image_loader --args="type=x300,addr=192.168.10.3,fpga=HG"
> [INFO] [UHD] linux; GNU C++ version 4.8.4; Boost_105400; UHD_4.0.0.rfnoc-devel-348-g2c2e1a99
> Unit: USRP X310 (F5BE96, 192.168.10.3)
> FPGA Image: /home/ltorresf/local/share/uhd/images/usrp_x310_fpga_HG.bit
> failed.
> Error: RuntimeError: Device reported an error during initialization.
> ltorresf at pc1:~$ 
>  
>  
>  
>  
> _______________________________________________
> USRP-users mailing list
> USRP-users at lists.ettus.com
> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com





More information about the USRP-users mailing list