[USRP-users] X310 product code unknown EEPROM

Marcus D. Leech mleech at ripnet.com
Wed Mar 23 20:50:52 EDT 2016


On 03/23/2016 06:09 PM, Diyar Muhammed via USRP-users wrote:
> Dear All,
> I assembled usrp x310, and I had a warning, so I downloaded FPGA image 
> and then I have upgraded FPGA by using the command: 
> usrp_x3xx_fpga_burner --addr=192.168.10.2 
> --fpga-path=/usr/local/share/uhd/images/usrp_x310_fpga_HGS.bit.
> after that the usrp x310 is able to find daughter board, but still I 
> have a UHD warning as shown in the below, as shown below:
>
> mint at mint ~ $ uhd_usrp_probe 192.168.10.2
> linux; GNU C++ version 4.8.2; Boost_105400; UHD_003.008.001-105-g91ae742f
>
You have a newer X310 hardware version that isn't supported by that 
very-old version of UHD.  Newer X310s *CANNOT* be supported by
   older UHD due to hardware changes that were made.

Upgrade to 3.9.2 or the just-released 3.9.3  UHD version.


>
> UHD Warning:
>     X300 unknown product code in EEPROM: 30818
>
> UHD Warning:
>     X300 unknown product code in EEPROM: 30818
>
> UHD Warning:
>     X300 unknown product code in EEPROM: 30818
>
> UHD Warning:
>     X300 unknown product code in EEPROM: 30818
> -- X300 initialization sequence...
> -- Determining maximum frame size... 1472 bytes.
> -- Setup basic communication...
> -- Loading values from EEPROM...
>
> UHD Warning:
>     X300 unknown product code in EEPROM: 30818
> -- Setup RF frontend clocking...
> -- Radio 1x clock:200
> -- Initialize Radio control...
> -- Performing register loopback test... pass
> -- Performing register loopback test... pass
> -- Initializing clock and time using internal sources... done
>   _____________________________________________________
>  /
> |       Device: X-Series Device
> |     _____________________________________________________
> |    /
> |   |       Mboard: X300?
> |   |   revision: 8
> |   |   product: 30818
> |   |   mac-addr0: 00:80:2f:23:7b:6f
> |   |   mac-addr1: 00:80:2f:23:7b:70
> |   |   gateway: 192.168.10.1
> |   |   ip-addr0: 192.168.10.2
> |   |   subnet0: 255.255.255.0
> |   |   ip-addr1: 192.168.20.2
> |   |   subnet1: 255.255.255.0
> |   |   ip-addr2: 192.168.30.2
> |   |   subnet2: 255.255.255.0
> |   |   ip-addr3: 192.168.40.2
> |   |   subnet3: 255.255.255.0
> |   |   serial: 30C0991
> |   |   FW Version: 3.0
> |   |   FPGA Version: 9.0
> |   |
> |   |   Time sources: internal, external, gpsdo
> |   |   Clock sources: internal, external, gpsdo
> |   |   Sensors: ref_locked
> |   | _____________________________________________________
> |   |    /
> |   |   |       RX DSP: 0
> |   |   |   Freq range: -100.000 to 100.000 MHz
> |   | _____________________________________________________
> |   |    /
> |   |   |       RX DSP: 1
> |   |   |   Freq range: -100.000 to 100.000 MHz
> |   | _____________________________________________________
> |   |    /
> |   |   |       RX Dboard: A
> |   |   |   ID: UBX-160 v1 (0x007a)
> |   |   |   Serial: 30C2AAB
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Frontend: 0
> |   |   |   |   Name: UBX RX
> |   |   |   |   Antennas: TX/RX, RX2, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 10.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Connection Type: IQ
> |   |   |   |   Uses LO offset: No
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Codec: A
> |   |   |   |   Name: ads62p48
> |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
> |   | _____________________________________________________
> |   |    /
> |   |   |       RX Dboard: B
> |   |   |   ID: UBX-160 v1 (0x007a)
> |   |   |   Serial: 30C2A33
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Frontend: 0
> |   |   |   |   Name: UBX RX
> |   |   |   |   Antennas: TX/RX, RX2, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 10.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Connection Type: IQ
> |   |   |   |   Uses LO offset: No
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       RX Codec: B
> |   |   |   |   Name: ads62p48
> |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
> |   | _____________________________________________________
> |   |    /
> |   |   |       TX DSP: 0
> |   |   |   Freq range: -100.000 to 100.000 MHz
> |   | _____________________________________________________
> |   |    /
> |   |   |       TX DSP: 1
> |   |   |   Freq range: -100.000 to 100.000 MHz
> |   | _____________________________________________________
> |   |    /
> |   |   |       TX Dboard: A
> |   |   |   ID: UBX-160 v1 (0x0079)
> |   |   |   Serial: 30C2AAB
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Frontend: 0
> |   |   |   |   Name: UBX TX
> |   |   |   |   Antennas: TX/RX, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 10.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Connection Type: QI
> |   |   |   |   Uses LO offset: No
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Codec: A
> |   |   |   |   Name: ad9146
> |   |   |   |   Gain Elements: None
> |   | _____________________________________________________
> |   |    /
> |   |   |       TX Dboard: B
> |   |   |   ID: UBX-160 v1 (0x0079)
> |   |   |   Serial: 30C2A33
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Frontend: 0
> |   |   |   |   Name: UBX TX
> |   |   |   |   Antennas: TX/RX, CAL
> |   |   |   |   Sensors: lo_locked
> |   |   |   |   Freq range: 10.000 to 6000.000 MHz
> |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> |   |   |   |   Connection Type: QI
> |   |   |   |   Uses LO offset: No
> |   |   | _____________________________________________________
> |   |   |    /
> |   |   |   |       TX Codec: B
> |   |   |   |   Name: ad9146
> |   |   |   |   Gain Elements: None
>
> mint at mint ~ $
>
> What I have to do to sort out that?
> in advance many thanks.





More information about the USRP-users mailing list