[USRP-users] Master Clock Supression
dwwkelly at gmail.com
Fri Jul 17 15:45:13 EDT 2015
I'm not sure what you mean by offset tuning. Is that like just tuning to
avoid the tone? Or, is it like the tone might have less power at different
frequencies I tune to (like tuning to 3.0505 GHz might give me a lower
tone-power than 3.5 GHz)?
On Fri, Jul 17, 2015 at 3:15 PM, <mleech at ripnet.com> wrote:
> Try with offset tuning. If they're still there, then they are probably
> actual clock spurs, rather than enhanced LO
> On 2015-07-17 15:04, devin kelly via USRP-users wrote:
> Right now I've got two X310s each with two UBXs. I have each TX/RX
> antenna on subdev A connected to each other (with 40 dB of attenuation),
> same for each B subdev. I have all the RX2 antennas terminated.
> I see the tones on regardless of the subdev/antenna combination. I also
> tried connecting a spectrum analyzer to the TX/RX antenna ports and saw no
> tones. I also put an antenna on my spectrum analyzer and saw no tones over
> the air with the antenna right next to each X310.
> Thanks Again,
> On Fri, Jul 17, 2015 at 11:19 AM, Marcus Müller <
> usrp-users at lists.ettus.com> wrote:
>> Shielding/separation-wise, the X310 should be pretty much superior in
>> every aspect -- not only is the ADC, DAC, mixer, amplifier and LO
>> synthesizers in one package on the B2x0 (the AD9361); the X310 is modular
>> in the sense that the MCR doesn't even appear to the daugtherboards,
>> necessarily; it's an FPGA-only clock, generated by the clock distribution
>> IC on the mainboard, and the UBX, especially to suppress strong
>> interferers, has a metal can (which is unique among our RF hardware, so
>> far). Under that metal can, there's a lot of partitions, which align with
>> the different jobs and frequency ranges on the board, compare the schematic
>> So since you're seeing 200MHz-harmonics, these might either spuriously
>> get into the antenna ports, or for some reason, at multiples of 200MHz LO
>> leakage is worse (I don't expect that). Have you tried using offset tuning
>>  to reduce these spurs?
>> Best regards,
>>  http://files.ettus.com/schematics/ubx/ubx.pdf
>> On 17.07.2015 17:03, devin kelly via USRP-users wrote:
>> I have an X310 with a UBX daughtercard. I've noticed that there are
>> tones every 200 MHz (I checked 2.4GHx, 2.6 GHz, 2.8 GHz, 3 GHz, 3.2 GHz).
>> Do I have any options for suppressing the tones? Is there any shielding or
>> RF absorber I can add somewhere?
>> The B210s seem to have each section of radio gated off (to make it easier
>> to add shielding?). But the X310s don't as far as I can tell.
>> Thanks for any help,
>> USRP-users mailing listUSRP-users at lists.ettus.comhttp://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
>> USRP-users mailing list
>> USRP-users at lists.ettus.com
> USRP-users mailing listUSRP-users at lists.ettus.comhttp://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the USRP-users