[USRP-users] Fwd: Re: X310 + 2 CBX daughtercards strange behaviour

Marcus D. Leech mleech at ripnet.com
Tue Sep 23 10:04:50 EDT 2014


On 09/23/2014 09:07 AM, boeglen herve via USRP-users wrote:
>
> Hi all,
>
> I didn't get any answer to this email so I send it again :-)
>
> Does anybody on the list use a X300 or X310 equipped with 2 radio 
> boards and 10Gbit interface ? If so, have they already tested a 
> simultaneous TX or RX?
>
> This problem looks to me as if the second daughter card is not 
> configured properly.
>
> Thank you for your answers.
>
> Best regards
>
> Hervé
>
I have two boards, and a 1GiGe interface.  I'll test in a few minutes, 
but I suspect it will all work just fine.


> -------- Original Message --------
>
> Subject: 	Re: [USRP-users] X310 + 2 CBX daughtercards strange behaviour
> Date: 	Sat, 20 Sep 2014 09:35:19 +0200
> From: 	boeglen herve <herve.boeglen at univ-poitiers.fr>
> To: 	"Marcus D. Leech" <mleech at ripnet.com>
> Cc: 	Mike Jameson <mike.jameson at ettus.com>, <usrp-users at lists.ettus.com>
>
> Hi,
>
> I know pretty well the throughput limit of the 1Gbit interface, that's 
> why I  use a 10 Gbit one :-) It's really impressive since it holds the 
> 100Ms/s using both channels. My machine runs a Core I7 2600k + 12 
> Gbyte RAM on Ubuntu 14.04 64 bit (3.13 kernel, MTU set to 9000!). I 
> use the latest firmware with GNURadio 3.7.5.
>
> Concerning my problem, RF 0 channel (first CBX) has a noise floor 
> around -100 dB on the spectum scope whereas RF 1 (second CBX) goes up 
> to -60 dB. However my settings are the same for both channels.
>
> When mentioning the bandwidth, It was to describe the behaviour of the 
> signal on RF 1 (wider noise bandwidth).
>
> Another noticeable difference between the two channels is that you get 
> a -55dB spike at 0Hz on RF 1. When performing the Wifi test, everytime 
> a packet enters, RF 1 channel's noise floor increases around -60dB 
> (over the 50MHz bandwidth). Really weird...
>
> Best regards
>
> Hervé
>
> On Fri, 19 Sep 2014 17:16:20 -0400, Marcus D. Leech wrote:
>
>         Hi Markus and Mike, Thank you for your answers. It does not
>         change anything whether you specify the subdev or not. Markus:
>         yes everything is wired properly. Concerning the last email, I
>         used a BladeRF as a generator (0dBm + 30dB attenuator). Here
>         is another test with Wifi and as you can see from the two
>         spectrum scopes (upper is RF 1, lower RF 0), RF 1 reception
>         bandwith seems to be larger than for RF 0 (however it's set to
>         20MHz for both channels). I have a second X310 with the same
>         daugthercards and I get the same behaviour... Is there a way
>         to use just RF 1? I hope that going to sleep is going to help
>         me to find an idea to solve the problem :-) Best regards Hervé
>
>     The bandwidth setting doesn't do anything on the CBX card--it's only
>     used to set the analog bandwidth between the cards baseband/IF output, and
>         the ADC.
>
>     The bandwidth delivered to the host depends, in this case, on the
>     specified sample rate.
>
>     What type of host interface are you using in this case?  From the
>     spectrum plots, it looks like you're asking for two channels of 25Msps
>     each, which
>         will not "fit" over 1GiGe at 16-bit samples.
>
>     Do you get any 'O' being output while you run this flow-graph?  What
>     type of computer?
>
>
>
>
>
> _______________________________________________
> USRP-users mailing list
> USRP-users at lists.ettus.com
> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com


-- 
Marcus Leech
Principal Investigator
Shirleys Bay Radio Astronomy Consortium
http://www.sbrac.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/attachments/20140923/bd536f6c/attachment-0002.html>


More information about the USRP-users mailing list