[USRP-users] Replacing DSP in N2x0

Wilson, Jeffery (DS-1) JAWilson at drs-ds.com
Wed Feb 15 14:54:47 EST 2012


Designation: Non-SSA/Finmeccanica 

Ian,

 

Thank you for all the info. I'm not a DSP guy myself, so I don't fully
understand the issues, in fact it may be elsewhere in the DSP module
than the CORDIC. We certainly need to do more testing before we start
changing things, and simulations as you suggest may be the way to go.

 

-- Jeff

 

3.1.1001

From: Ian Buckley [mailto:ianb at ionconcepts.com] 
Sent: Tuesday, February 14, 2012 3:51 PM
To: Wilson, Jeffery (DS-1)
Cc: usrp-users at lists.ettus.com
Subject: Re: [USRP-users] Replacing DSP in N2x0

 

Jeff,

Yes, there are commercial users of the USRP H/W who have swapped some or
all of the signal processing H/W out for something custom, generally
because they want to do something unusual and very specific for their
application. I'm not personally aware of anyone having done what you
suggest (swap out the CORDIC for another DDFS implementation), but it
would be a relatively easy  task as that portion of the design is
largely simple streaming data and an uber simple 32bit bus used to
program the various registers that program the DDC frequency etc. The
only consequence to the system as a whole I can think of off hand is
that you might change the number of DSPCLK cycles of latency between an
"off-air signal" being sampled and it being time stamped in the
downstream vita logic, and that you might need to modify firmware so
that the appropriate frequency value is programmed for your own DDC
implantation.

 

Perhaps as a first you should simulate the CORDIC in isolation with test
data and compare that with a reference model and/or alternate DDFS
implementation such as a lookup table as a first step to establish if
your supposition is correct? 

 

Removal of the TX DSP is trivial, track down dsp_core_tx, it contains
most of the TX data path and comment it out...you should probably tie
the strobe signal passing upstream to the vita logic.

 

-Ian

 

 

On Feb 14, 2012, at 12:14 PM, Wilson, Jeffery (DS-1) wrote:

 

Designation: Non-SSA/Finmeccanica

Hello,

 

I've been running some tests using an N200 (I also have an N210 at my
disposal), and I'm a bit unhappy with the performance of the RX DSP
(most likely the CORDIC itself). I wasn't able to find much by searching
the list archives or the web, but I was wondering if it is at all common
for users to swap out the UHD implementation for a separate and/or
proprietary IP core with better characteristics. Could anyone point me
to any examples of this (if they exist)?

 

I also remember seeing something at one time about removing the whole TX
chain to make more room on the FPGA for RX-only applications, but
haven't been able to relocate it. I'd appreciate it if someone could
point me to that info as well.

 

Thanks,

 

--

Jeff Wilson

Software Engineer

DRS Signal Solutions, Inc.

Direct: 301.944.8772

 

3.1.1001

_______________________________________________
USRP-users mailing list
USRP-users at lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/attachments/20120215/27be1d42/attachment-0002.html>


More information about the USRP-users mailing list